I have a 96 xj i need to replace the rear wiper bezel, does anybody know how to remove the wiper arm? i tried pulling it but that didn't work, i looked for some sort of clip to push but didn't see one thanks...

[QUOTE=runuover]pull the clip out and the wiper back and wiggel it and it should come out. its a little slide clip.

lift the blade off the window look on the arm right were it goes to the motor. you will see a small clip that you can slide out about 1/4" than let go of the blade and grab the arm move shake alittle it will than pull off.


hope this helps

If it is like most other Chrysler products you may have to fight it off. Typicly when we replace caravan and voyager back windows and windshields the wipers are a bear to get off. You can try to heat it with a propane torch, you don't have to get crazy, just a little bit of heat and some muscle will get it off. Usually they are rusted or corroded on there. If and when you get it off, clean up the splines and put a dab of grease on it to reduce future corrosion.

If you didn't get it off yet let me know. I have a 96 I can go look :banghead:

If you didn't get it off yet let me know. I have a 96 I can go look :banghead:

No the Damn thing will not budge i ripped out what i think was the clip so ........................ :1zhelp:

just got home I'll go out right now and look brb

lift the blade off the window look on the arm right were it goes to the motor. you will see a small clip that you can slide out about 1/4" than let go of the blade and grab the arm move shake alittle it will than pull off.


hope this helps

OK THIS WAS WRONG JUST WENT OUTSIDE AND LOOKED.:banghead:

Lift the arm,you will see a little hole were it pivots
You have to put something in the hole .like a 6 pen Nail
To hold it off the glass. Than let go of the arm
(It should be about 1“off the glass not holding it ) now
Look you will see under it a little clip push the clip in and
Pull on the wiper arm at same time . That should do it.

OK THIS WAS WRONG JUST WENT OUTSIDE AND LOOKED.:banghead:

Lift the arm,you will see a little hole were it pivots
You have to put something in the hole .like a 6 pen Nail
To hold it off the glass. Than let go of the arm
(It should be about 1“off the glass not holding it ) now
Look you will see under it a little clip push the clip in and
Pull on the wiper arm at same time . That should do it.

Yeah that's the clip i ripped out.. ill try something else i hope will work

I think you need to push in on that clip :)

I think you need to push in on that clip :)
i am having the same problem i need to treplace the whole wiper did you figured out how to remove it??? please help thanks

[/I] if you look 2 posts up thats how i got mine off

Yeah that's the clip i ripped out.. ill try something else i hope will work

Ok I NOW have the wiper off but i cant sem to get the bezel off i am unable to get the nut to unscrew. i can get it to turn but it will not move up or down it seems like it is stuck HELP
:banghead:

Bend the wiper arm back and that will release it. Try that.thats what i did to replace it.

Bend the wiper arm back and that will release it. Try that.thats what i did to replace it.
I have the wiper asrm off, its the screw thats on there that wont come off ive tried to unscrew it both ways, it will move but it seems stuck where its at......... it just turns :confused:

Put some wd-40 on that. turn to the left.

Put some wd-40 on that. turn to the left.

Getting it to turn is the easy part its getting it to come off the screw is where i am having the problem it will spin in either direction but wont move up or down :banghead: